Just How to Replace a Tub

Free Estimates

We have discovered the article about Installing A Bathtub directly below on the internet and believe it made perfect sense to share it with you here.


Tools You Need to Install a New Bathtub
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably hard job. If the old bathtub is conveniently available, the job can move rapidly; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually certified yourself for the task and also fit attempting it. Instead of working with a contractor to take over a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't need to alter the setup of your previous water pipes.
Your tools and material list must consist of the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
    Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipelines.
    If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Safeguard the tap in place with the supplier offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Installing the Bath tub


    Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
    The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
    To install taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
    Activate the supply of water as well as check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Load the tub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
    Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it right into its final setting.

    Planning for the Setup


    To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
    Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last position.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
    You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealer can split fairly early if you do not take into account this activity before sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the market. It is suggested to fit the ceramic tiles using water-resistant or water-proof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I'm certainly very fascinated by How to Install a Bathtub Yourself and I really hope you enjoyed reading the new blog entry. Sharing is nice. One never knows, you may just be helping someone out. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.



    Book Today!

    Leave a Reply

    Your email address will not be published. Required fields are marked *